Abstract
Orange peel waste offers a potential particulate filler for polymer composites, but its influence depends on particle size, loading, and the property being considered. This experimental study examines polyester composites containing orange peel particles with nominal sizes of 125, 212, and 250 μm at mass fractions of 2, 4, 6, and 8 wt.%, alongside unfilled polyester. The peels were washed, oven-dried at 60 °C for 30 min, ground, and separated into the three size fractions before mixing and casting. The reported measurements comprise tensile stress–strain behavior, tensile strength, Young’s modulus, flexural strength, Shore D hardness, and thermal conductivity. The summary plots indicate that the 125 μm fraction generally produced the highest values, with tensile strength, modulus, and flexural strength reaching their highest reported measurement values at 6 wt.%. Young’s modulus increased from 385 to 674 MPa, whereas hardness increased from 36.8 to 66.36 Shore D units and reached its maximum at 8 wt.%. Thermal conductivity increased from 0.00109 to 0.03673 W/(m·K). The tensile-strength summary reports an increase from 29.504 to 50.592 MPa, although its unfilled reference conflicts with the stress–strain curves and requires reconciliation. The results suggest property-specific responses rather than a single optimum formulation: additional filler beyond 6 wt.% reduced several mechanical responses while hardness and conductivity continued to increase for the smallest particles. Missing uncertainty estimates and an unresolved tensile-reference discrepancy limit quantitative interpretation. The findings support further evaluation of orange peel as a polyester filler, without establishing biodegradability, improved thermal insulation, or application-level performance.
Keywords: Orange Peel Waste; Polyester Composites; Particle Size; Mechanical Properties; Shore D Hardness; Thermal Conductivity
Abstract
Orange peel waste offers a potential particulate filler for polymer composites, but its influence depends on particle size, loading, and the property being considered. This experimental study examines polyester composites containing orange peel particles with nominal sizes of 125, 212, and 250 μm at mass fractions of 2, 4, 6, and 8 wt.%, alongside unfilled polyester. The peels were washed, oven-dried at 60 °C for 30 min, ground, and separated into the three size fractions before mixing and casting. The reported measurements comprise tensile stress–strain behavior, tensile strength, Young’s modulus, flexural strength, Shore D hardness, and thermal conductivity. The summary plots indicate that the 125 μm fraction generally produced the highest values, with tensile strength, modulus, and flexural strength reaching their highest reported measurement values at 6 wt.%. Young’s modulus increased from 385 to 674 MPa, whereas hardness increased from 36.8 to 66.36 Shore D units and reached its maximum at 8 wt.%. Thermal conductivity increased from 0.00109 to 0.03673 W/(m·K). The tensile-strength summary reports an increase from 29.504 to 50.592 MPa, although its unfilled reference conflicts with the stress–strain curves and requires reconciliation. The results suggest property-specific responses rather than a single optimum formulation: additional filler beyond 6 wt.% reduced several mechanical responses while hardness and conductivity continued to increase for the smallest particles. Missing uncertainty estimates and an unresolved tensile-reference discrepancy limit quantitative interpretation. The findings support further evaluation of orange peel as a polyester filler, without establishing biodegradability, improved thermal insulation, or application-level performance.
Keywords: Orange Peel Waste; Polyester Composites; Particle Size; Mechanical Properties; Shore D Hardness; Thermal Conductivity
- Pagliarini, E.; Minichiello, C.; Sisti, L.; Totaro, G.; Baffoni, L.;
Di Gioia, D.; Saccani, A. (2024). From food waste to eco-friendly
functionalized polymer composites: Investigation of orange peels as
active filler. New Biotechnology, 80, 37-45. https://doi.org/10.1016/j.nbt.2024.01.001
- Yaradoddi, J. S.; Banapurmath, N. R.; Ganachari, S. V.; Soudagar, M.
E. M.; Sajjan, A. M.; Kamat, S.; Mujtaba, M. A.; Shettar, A. S.; Anqi,
A. E.; Safaei, M. R.; Elfasakhany, A.; Siddiqui, M. I. H.; Ali, M. A.
(2022). Bio-based material from fruit waste of orange peel for
industrial applications. Journal of Materials Research and
Technology, 17, 3186–3197. https://doi.org/10.1016/j.jmrt.2021.09.016
- Sable, S.; Ikar, M.; Lagad, P.; Gosake, S.; Mule, H.; Khadtale, H.
(2024). Investigating the Complexities of Plastic Recycling Challenges
and Revolutionary Strides in Orange Peel Biofilm Research.
Industrial Engineering Journal, 53(4, No. 4), 118–127.
- Wale, S. R.; Patil, S. D.; Mahalle, S. P.; Bahiram, G. S.; Korat, J.
R. (2024). Bioplastics From Fruit Waste: A Trade Opportunity in a Green
Future. Madras Agricultural Journal, 111(7–9). https://doi.org/10.29321/MAJ.10.500003
- Yaradoddi, J. S.; Banapurmath, N. R.; Ganachari, S. V.; Soudagar, M.
E. M.; Mubarak, N. M.; Hallad, S.; Hugar, S.; Fayaz, H. (2020).
Biodegradable carboxymethyl cellulose based material for sustainable
packaging application. Scientific Reports, 10(1), 21960. https://doi.org/10.1038/s41598-020-78912-z
- Hasan, M.; Utami, A.; Siregar, C.; Hanum, L.; Khaldun, I.; Nazar, M.
(2025). Thermal, structural and mechanical characterization of
bio-nanocomposite films from purple sweet potato starch/chitosan
nanoparticles integrated with anthocyanin extract. Results in
Engineering, 25, 104448. https://doi.org/10.1016/j.rineng.2025.104448
- Paul, V. (2015). Synthesis and characterization of a biocomposite
derived from banana plants (Musa cavendish). Doctoral thesis, Durban
University of Technology, Durban, South Africa. https://doi.org/10.51415/10321/1286
- Ibraheem, E. K.; Bdaiwi, W. (2024). Enhancing Mechanical and Thermal
Properties of Unsaturated Polyester Composites Through Sidr Leaves’
Particle Reinforcement. Revue des Composites et des Matériaux
Avancés, 34(3), 269-275. https://doi.org/10.18280/rcma.340301
- Radam, A. O.; Khadim, A. I.; Abdul-Ridha, Z. S. (2022). Studying of
Mechanical and Physical Properties of Polyester Composite Reinforced by
Cows and Buffalo Horns. NeuroQuantology, 20(1), 17-27. https://doi.org/10.14704/nq.2022.20.1.nq22003
- Abdulkader, N. J.; Abdula, A. M.; Ahmed, S. S. (2020). Mechanical
Properties of Polyester Matrix Composites Reinforced with Waste Marble
Particles. IOP Conference Series: Materials Science and
Engineering, 978(1), 012034. https://doi.org/10.1088/1757-899x/978/1/012034
- Majeed, A. H.; Ibrahim, S. Q. (2017). Mechanical Properties of
Unsaturated Polyester Filled With Silica Fume, Glass Powder and Carbon
Black. Engineering and Technology Journal, 35(6), 640-647. https://doi.org/10.30684/etj.35.6a.12
- Alam, M. K.; Islam, M. T.; Mina, M. F.; Gafur, M. A. (2014).
Structural, mechanical, thermal, and electrical properties of carbon
black reinforced polyester resin composites. Journal of Applied
Polymer Science, 131(13), 40421. https://doi.org/10.1002/app.40421
- Metteb, Z. W.; Hamdan, Z. K.; Jebur, N. A.; Shokrollahi, H.; Abdull,
F. A.; Ogaili, A. A. F. (2026). Mechanical and Sustainable Performance
of Polyester Composites with Glass and Natural Waste Fiber Fillers.
Journal of Engineering and Sustainable Development, 30(2),
253-261. https://doi.org/10.31272/jeasd.3186
- Balaji, N. S.; Asokan, P. (2023). Influence of Fabrication Parameters
on Thermo-Mechanical Characteristics of Zea Natural Fiber Reinforced
Polymer Composites. Iranian Journal of Chemistry and Chemical
Engineering, 42(2). https://doi.org/10.30492/ijcce.2022.546145.5095
- Kumar, A.; Jyske, T.; Möttönen, V. (2020). Properties of Injection
Molded Biocomposites Reinforced with Wood Particles of Short-Rotation
Aspen and Willow. Polymers, 12(2), 257. https://doi.org/10.3390/polym12020257
- Mekonnen, B. Y.; Mamo, Y. J. (2020). Tensile and Flexural Analysis of
a Hybrid Bamboo/Jute Fiber-reinforced Composite with Polyester Matrix as
a Sustainable Green Material for Wind Turbine Blades. International
Journal of Engineering, 33(2), 314–319. https://doi.org/10.5829/ije.2020.33.02b.16
- Nurazzi, N. M.; Asyraf, M. R. M.; Khalina, A.; Abdullah, N.; Aisyah,
H. A.; Rafiqah, S. A.; Sabaruddin, F. A.; Kamarudin, S. H.; Norrrahim,
M. N. F.; Ilyas, R. A.; Sapuan, S. M. (2021). A Review on Natural Fiber
Reinforced Polymer Composite for Bullet Proof and Ballistic
Applications. Polymers, 13(4), 646. https://doi.org/10.3390/polym13040646
- Wazalwar, R.; Tripathi, N.; Raichur, A. M. (2021). Mechanical and
curing behavior of epoxy composites reinforced with polystyrene-graphene
oxide (PS-GO) core-shell particles. Composites Part C: Open
Access, 5, 100128. https://doi.org/10.1016/j.jcomc.2021.100128
- Hunain, M. B.; Alnomani, S. N.; Razzaq, Q. (2021). An Investigation
of Tensile and Thermal Properties of Epoxy Polymer Modified by Activated
Carbon Particle. IOP Conference Series: Materials Science and
Engineering, 1094(1), 012164. https://doi.org/10.1088/1757-899X/1094/1/012164
- Rehman, M. M.; Shaker, K.; Nawab, Y. (2022). Effect of PEEK Particles
on Physiomechanical Behavior of Carbon/Epoxy Composite.
International Journal of Polymer Science, 2022, 8161684. https://doi.org/10.1155/2022/8161684
- Immanuel Durai Raj, J.; Durairaj, R. I. B.; John Rajan, A.;
Barmavatu, P. (2023). Effect of e-waste nanofillers on the mechanical,
thermal, and wear properties of epoxy-blend sisal woven fiber-reinforced
composites. Green Processing and Synthesis, 12(1), 20230164. https://doi.org/10.1515/gps-2023-0164
- Wang, M.; Ma, L.; Li, B.; Zhang, W.; Zheng, H.; Wu, G.; Huang, Y.;
Song, G. (2020). One-step generation of silica particles onto graphene
oxide sheets for superior mechanical properties of epoxy composite and
scale application. Composites Communications, 22, 100514. https://doi.org/10.1016/j.coco.2020.100514
- Ibrahim, A. D.; Aleabi, S. H.; Mahdi, K. H. (2025). Preparing
Composite Materials Based on Unsaturated Polyester with Natural
Materials of Plant Origin and Studying Some of Their Mechanical and
Physical Properties. Ibn Al-Haitham Journal for Pure and Applied
Sciences, 38(3), 125–136. https://doi.org/10.30526/38.3.3972
- Alshgari, R. A.; Anandaram, H.; Kistan, A.; Nisha, N.; Vel, V. M.;
Anitha, G.; Wabaidur, S. M.; Islam, M. A.; Alemayehu, A. (2022).
Experimental Investigations on the Mechanical Characteristics of Natural
Fiber Particle-Reinforced Polymer Composites under Cryogenic
Environment. Journal of Nanomaterials, 2022(1), 1864169. https://doi.org/10.1155/2022/1864169
- Rasheed, A. K.; Rasheed, N. K.; Marhoon, I. I. (2018). Thermal and
Natural Particles Addition Effects on the Mechanical and Physical
Properties of Epoxy–Polyurethane Resin Blend Polymer. European
Journal of Engineering Research and Science, 3(8), 1–4. https://doi.org/10.24018/ejers.2018.3.8.836
How to cite:
Adil I. Kadim, Zainab Waleed Ahmed, Zainab S. Abdul-Ridha, Bushra H. Hussein, Hind W. Abdullah. Improving the thermal and mechanical features of polyester reinforced with orange peel waste micro-particles. Revista Cultura Científica, 2026 Issue 24. pg. 2417-2427.
Publication History
-
Received: 19/06/2026
-
Accepted: 21/10/2026
-
Published: 07/11/2026
Copyright © 2026, Adil I. Kadim, Zainab Waleed Ahmed, Zainab S. Abdul-Ridha, Bushra H. Hussein, Hind W. Abdullah. Published by Revista Cultura Científica. This article is published as open access under the Creative Commons Attribution 4.0 International (CC BY 4.0) license (
http://creativecommons.org/licenses/by/4.0/).