Improving the thermal and mechanical features of polyester reinforced with orange peel waste micro-particles

Adil I. Kadim1, Zainab Waleed Ahmed2, Zainab S. Abdul-Ridha2, Bushra H. Hussein1, Hind W. Abdullah3
1Department of Physics, College of Education for Pure Sciences (Ibn Al-Haitham), University of Baghdad, Baghdad, Iraq
2Directorate General of Education, Baghdad Al-Rusafa First, Ministry of Education, Baghdad, Iraq
3Department of Physics, College of Science, University of Diyala, Diyala, Iraq
DOI: https://doi.org/10.70517/revcc2624194
Published: 07/11/2026
: Adil I. Kadim, Zainab Waleed Ahmed, Zainab S. Abdul-Ridha, Bushra H. Hussein, Hind W. Abdullah. Improving the thermal and mechanical features of polyester reinforced with orange peel waste micro-particles. Revista Cultura Científica, 2026 Issue 24. pg. 2417-2427.

Abstract

Orange peel waste offers a potential particulate filler for polymer composites, but its influence depends on particle size, loading, and the property being considered. This experimental study examines polyester composites containing orange peel particles with nominal sizes of 125, 212, and 250 μm at mass fractions of 2, 4, 6, and 8 wt.%, alongside unfilled polyester. The peels were washed, oven-dried at 60 °C for 30 min, ground, and separated into the three size fractions before mixing and casting. The reported measurements comprise tensile stress–strain behavior, tensile strength, Young’s modulus, flexural strength, Shore D hardness, and thermal conductivity. The summary plots indicate that the 125 μm fraction generally produced the highest values, with tensile strength, modulus, and flexural strength reaching their highest reported measurement values at 6 wt.%. Young’s modulus increased from 385 to 674 MPa, whereas hardness increased from 36.8 to 66.36 Shore D units and reached its maximum at 8 wt.%. Thermal conductivity increased from 0.00109 to 0.03673 W/(m·K). The tensile-strength summary reports an increase from 29.504 to 50.592 MPa, although its unfilled reference conflicts with the stress–strain curves and requires reconciliation. The results suggest property-specific responses rather than a single optimum formulation: additional filler beyond 6 wt.% reduced several mechanical responses while hardness and conductivity continued to increase for the smallest particles. Missing uncertainty estimates and an unresolved tensile-reference discrepancy limit quantitative interpretation. The findings support further evaluation of orange peel as a polyester filler, without establishing biodegradability, improved thermal insulation, or application-level performance.

Keywords: Orange Peel Waste; Polyester Composites; Particle Size; Mechanical Properties; Shore D Hardness; Thermal Conductivity

Abstract

Orange peel waste offers a potential particulate filler for polymer composites, but its influence depends on particle size, loading, and the property being considered. This experimental study examines polyester composites containing orange peel particles with nominal sizes of 125, 212, and 250 μm at mass fractions of 2, 4, 6, and 8 wt.%, alongside unfilled polyester. The peels were washed, oven-dried at 60 °C for 30 min, ground, and separated into the three size fractions before mixing and casting. The reported measurements comprise tensile stress–strain behavior, tensile strength, Young’s modulus, flexural strength, Shore D hardness, and thermal conductivity. The summary plots indicate that the 125 μm fraction generally produced the highest values, with tensile strength, modulus, and flexural strength reaching their highest reported measurement values at 6 wt.%. Young’s modulus increased from 385 to 674 MPa, whereas hardness increased from 36.8 to 66.36 Shore D units and reached its maximum at 8 wt.%. Thermal conductivity increased from 0.00109 to 0.03673 W/(m·K). The tensile-strength summary reports an increase from 29.504 to 50.592 MPa, although its unfilled reference conflicts with the stress–strain curves and requires reconciliation. The results suggest property-specific responses rather than a single optimum formulation: additional filler beyond 6 wt.% reduced several mechanical responses while hardness and conductivity continued to increase for the smallest particles. Missing uncertainty estimates and an unresolved tensile-reference discrepancy limit quantitative interpretation. The findings support further evaluation of orange peel as a polyester filler, without establishing biodegradability, improved thermal insulation, or application-level performance.

Keywords: Orange Peel Waste; Polyester Composites; Particle Size; Mechanical Properties; Shore D Hardness; Thermal Conductivity
  1. Pagliarini, E.; Minichiello, C.; Sisti, L.; Totaro, G.; Baffoni, L.; Di Gioia, D.; Saccani, A. (2024). From food waste to eco-friendly functionalized polymer composites: Investigation of orange peels as active filler. New Biotechnology, 80, 37-45. https://doi.org/10.1016/j.nbt.2024.01.001

  2. Yaradoddi, J. S.; Banapurmath, N. R.; Ganachari, S. V.; Soudagar, M. E. M.; Sajjan, A. M.; Kamat, S.; Mujtaba, M. A.; Shettar, A. S.; Anqi, A. E.; Safaei, M. R.; Elfasakhany, A.; Siddiqui, M. I. H.; Ali, M. A. (2022). Bio-based material from fruit waste of orange peel for industrial applications. Journal of Materials Research and Technology, 17, 3186–3197. https://doi.org/10.1016/j.jmrt.2021.09.016

  3. Sable, S.; Ikar, M.; Lagad, P.; Gosake, S.; Mule, H.; Khadtale, H. (2024). Investigating the Complexities of Plastic Recycling Challenges and Revolutionary Strides in Orange Peel Biofilm Research. Industrial Engineering Journal, 53(4, No. 4), 118–127.

  4. Wale, S. R.; Patil, S. D.; Mahalle, S. P.; Bahiram, G. S.; Korat, J. R. (2024). Bioplastics From Fruit Waste: A Trade Opportunity in a Green Future. Madras Agricultural Journal, 111(7–9). https://doi.org/10.29321/MAJ.10.500003

  5. Yaradoddi, J. S.; Banapurmath, N. R.; Ganachari, S. V.; Soudagar, M. E. M.; Mubarak, N. M.; Hallad, S.; Hugar, S.; Fayaz, H. (2020). Biodegradable carboxymethyl cellulose based material for sustainable packaging application. Scientific Reports, 10(1), 21960. https://doi.org/10.1038/s41598-020-78912-z

  6. Hasan, M.; Utami, A.; Siregar, C.; Hanum, L.; Khaldun, I.; Nazar, M. (2025). Thermal, structural and mechanical characterization of bio-nanocomposite films from purple sweet potato starch/chitosan nanoparticles integrated with anthocyanin extract. Results in Engineering, 25, 104448. https://doi.org/10.1016/j.rineng.2025.104448

  7. Paul, V. (2015). Synthesis and characterization of a biocomposite derived from banana plants (Musa cavendish). Doctoral thesis, Durban University of Technology, Durban, South Africa. https://doi.org/10.51415/10321/1286

  8. Ibraheem, E. K.; Bdaiwi, W. (2024). Enhancing Mechanical and Thermal Properties of Unsaturated Polyester Composites Through Sidr Leaves’ Particle Reinforcement. Revue des Composites et des Matériaux Avancés, 34(3), 269-275. https://doi.org/10.18280/rcma.340301

  9. Radam, A. O.; Khadim, A. I.; Abdul-Ridha, Z. S. (2022). Studying of Mechanical and Physical Properties of Polyester Composite Reinforced by Cows and Buffalo Horns. NeuroQuantology, 20(1), 17-27. https://doi.org/10.14704/nq.2022.20.1.nq22003

  10. Abdulkader, N. J.; Abdula, A. M.; Ahmed, S. S. (2020). Mechanical Properties of Polyester Matrix Composites Reinforced with Waste Marble Particles. IOP Conference Series: Materials Science and Engineering, 978(1), 012034. https://doi.org/10.1088/1757-899x/978/1/012034

  11. Majeed, A. H.; Ibrahim, S. Q. (2017). Mechanical Properties of Unsaturated Polyester Filled With Silica Fume, Glass Powder and Carbon Black. Engineering and Technology Journal, 35(6), 640-647. https://doi.org/10.30684/etj.35.6a.12

  12. Alam, M. K.; Islam, M. T.; Mina, M. F.; Gafur, M. A. (2014). Structural, mechanical, thermal, and electrical properties of carbon black reinforced polyester resin composites. Journal of Applied Polymer Science, 131(13), 40421. https://doi.org/10.1002/app.40421

  13. Metteb, Z. W.; Hamdan, Z. K.; Jebur, N. A.; Shokrollahi, H.; Abdull, F. A.; Ogaili, A. A. F. (2026). Mechanical and Sustainable Performance of Polyester Composites with Glass and Natural Waste Fiber Fillers. Journal of Engineering and Sustainable Development, 30(2), 253-261. https://doi.org/10.31272/jeasd.3186

  14. Balaji, N. S.; Asokan, P. (2023). Influence of Fabrication Parameters on Thermo-Mechanical Characteristics of Zea Natural Fiber Reinforced Polymer Composites. Iranian Journal of Chemistry and Chemical Engineering, 42(2). https://doi.org/10.30492/ijcce.2022.546145.5095

  15. Kumar, A.; Jyske, T.; Möttönen, V. (2020). Properties of Injection Molded Biocomposites Reinforced with Wood Particles of Short-Rotation Aspen and Willow. Polymers, 12(2), 257. https://doi.org/10.3390/polym12020257

  16. Mekonnen, B. Y.; Mamo, Y. J. (2020). Tensile and Flexural Analysis of a Hybrid Bamboo/Jute Fiber-reinforced Composite with Polyester Matrix as a Sustainable Green Material for Wind Turbine Blades. International Journal of Engineering, 33(2), 314–319. https://doi.org/10.5829/ije.2020.33.02b.16

  17. Nurazzi, N. M.; Asyraf, M. R. M.; Khalina, A.; Abdullah, N.; Aisyah, H. A.; Rafiqah, S. A.; Sabaruddin, F. A.; Kamarudin, S. H.; Norrrahim, M. N. F.; Ilyas, R. A.; Sapuan, S. M. (2021). A Review on Natural Fiber Reinforced Polymer Composite for Bullet Proof and Ballistic Applications. Polymers, 13(4), 646. https://doi.org/10.3390/polym13040646

  18. Wazalwar, R.; Tripathi, N.; Raichur, A. M. (2021). Mechanical and curing behavior of epoxy composites reinforced with polystyrene-graphene oxide (PS-GO) core-shell particles. Composites Part C: Open Access, 5, 100128. https://doi.org/10.1016/j.jcomc.2021.100128

  19. Hunain, M. B.; Alnomani, S. N.; Razzaq, Q. (2021). An Investigation of Tensile and Thermal Properties of Epoxy Polymer Modified by Activated Carbon Particle. IOP Conference Series: Materials Science and Engineering, 1094(1), 012164. https://doi.org/10.1088/1757-899X/1094/1/012164

  20. Rehman, M. M.; Shaker, K.; Nawab, Y. (2022). Effect of PEEK Particles on Physiomechanical Behavior of Carbon/Epoxy Composite. International Journal of Polymer Science, 2022, 8161684. https://doi.org/10.1155/2022/8161684

  21. Immanuel Durai Raj, J.; Durairaj, R. I. B.; John Rajan, A.; Barmavatu, P. (2023). Effect of e-waste nanofillers on the mechanical, thermal, and wear properties of epoxy-blend sisal woven fiber-reinforced composites. Green Processing and Synthesis, 12(1), 20230164. https://doi.org/10.1515/gps-2023-0164

  22. Wang, M.; Ma, L.; Li, B.; Zhang, W.; Zheng, H.; Wu, G.; Huang, Y.; Song, G. (2020). One-step generation of silica particles onto graphene oxide sheets for superior mechanical properties of epoxy composite and scale application. Composites Communications, 22, 100514. https://doi.org/10.1016/j.coco.2020.100514

  23. Ibrahim, A. D.; Aleabi, S. H.; Mahdi, K. H. (2025). Preparing Composite Materials Based on Unsaturated Polyester with Natural Materials of Plant Origin and Studying Some of Their Mechanical and Physical Properties. Ibn Al-Haitham Journal for Pure and Applied Sciences, 38(3), 125–136. https://doi.org/10.30526/38.3.3972

  24. Alshgari, R. A.; Anandaram, H.; Kistan, A.; Nisha, N.; Vel, V. M.; Anitha, G.; Wabaidur, S. M.; Islam, M. A.; Alemayehu, A. (2022). Experimental Investigations on the Mechanical Characteristics of Natural Fiber Particle-Reinforced Polymer Composites under Cryogenic Environment. Journal of Nanomaterials, 2022(1), 1864169. https://doi.org/10.1155/2022/1864169

  25. Rasheed, A. K.; Rasheed, N. K.; Marhoon, I. I. (2018). Thermal and Natural Particles Addition Effects on the Mechanical and Physical Properties of Epoxy–Polyurethane Resin Blend Polymer. European Journal of Engineering Research and Science, 3(8), 1–4. https://doi.org/10.24018/ejers.2018.3.8.836

Adil I. Kadim
Department of Physics, College of Education for Pure Sciences (Ibn Al-Haitham), University of Baghdad, Baghdad, Iraq
Zainab Waleed Ahmed
Directorate General of Education, Baghdad Al-Rusafa First, Ministry of Education, Baghdad, Iraq
Zainab S. Abdul-Ridha
Directorate General of Education, Baghdad Al-Rusafa First, Ministry of Education, Baghdad, Iraq
Bushra H. Hussein
Department of Physics, College of Education for Pure Sciences (Ibn Al-Haitham), University of Baghdad, Baghdad, Iraq
Hind W. Abdullah
Department of Physics, College of Science, University of Diyala, Diyala, Iraq

How to cite:

Adil I. Kadim, Zainab Waleed Ahmed, Zainab S. Abdul-Ridha, Bushra H. Hussein, Hind W. Abdullah. Improving the thermal and mechanical features of polyester reinforced with orange peel waste micro-particles. Revista Cultura Científica, 2026 Issue 24. pg. 2417-2427.

Publication History

Copyright © 2026, Adil I. Kadim, Zainab Waleed Ahmed, Zainab S. Abdul-Ridha, Bushra H. Hussein, Hind W. Abdullah. Published by Revista Cultura Científica. This article is published as open access under the Creative Commons Attribution 4.0 International (CC BY 4.0) license (http://creativecommons.org/licenses/by/4.0/).

Browse Advance Search